Showing posts with label on. Show all posts
Showing posts with label on. Show all posts

Thursday, September 26, 2013

Push Off Push On

The ubiquitous 555 has yet another airing with this bistable using a simple push-button to provide a push-on, push-off action. It uses the same principle of the stored charge in a capacitor taking a Schmitt trigger through its dead-band. Whereas the Schmitt trigger in that reference was made from discrete components, the in-built dead-band arising from the two comparators, resistor chain and bistable within the 555 is used instead. The circuit demonstrates a stand-by switch, the state of which is indicated by illumination of either an orange or red LED, exclusively driven by the bipolar output of pin 3. Open-collector output (pin 7) pulls-in a 100-mA relay to drive the application circuit; obviously if an ON status LED is provided elsewhere, then the relay, two LEDs and two resistors can be omitted, with pin 3 being used to drive the application circuit, either directly or via a transistor.

Circuit diagram:

push-off-push-on-circuit-diagramw

Push Off Push On Circuit Diagram

The original NE555 (non-CMOS) can source or sink 200 mA from / into pin 3. Component values are not critical; the ‘dead-band’ at input pins 2 and 6 is between 1/3 and 2/3 of the supply voltage. When the pushbutton is open-circuit, the input is clamped within this zone (at half the supply voltage) by two equal-value resistors, Rb. To prevent the circuit powering-up into an unknown condition, a power-up reset may be applied with a resistor from supply to pin 4 and capacitor to ground. A capacitor and high-value resistor (Rt) provide a memory of the output state just prior to pushing the button and creates a dead time, during which button contact bounce will not cause any further change. When the button is pressed, the stored charge is sufficient to flip the output to the opposite state before the charge is dissipated and clamped back into the neutral zone by resistors Rb. A minimum of 0.1 µF will work, but it is safer to allow for button contact-bounce or hand tremble; 10 µF with 220 k gives approximately a 2-second response.

Author: Trevor Skeggs - Copyright: Elektor July-August 2004

Source : www.extremecircuits.net

Read More..

Wednesday, April 10, 2013

Cellphone cannot power on repair tips

Cellphone cannot power on normally.
Check batteray first, try to turn on with a good batteray, if still problem :

1. Try to charging the cellphone
2. If the cellphone can be charging, probably power switch fault/broken
3. Check power switch first, replace with a good one if needed.
4. If the problem not solved, try to flash/upgrade software/firmware with a latest version
5. If the problem still not solved, resolder flash IC, replace if needed.
6. If the problem still not solved, probaby main engine/pcb broken.
7. Trace for broken circuit or swap engine.
Read More..

Wednesday, April 3, 2013

Protectors Circuit on SMPS power supply


The simplest example SMPS which still uses 3 transistors (C3807, A1015 and power transistors) classic problem that often occurs is: - Problem in the feedback circuit can cause the output voltage B + over so that it can endanger the aircraft as a whole. For example elco erupted, pcb burnt burnt by over-heated, horizontal transistor short.

- Problem on feedback circuits may cause power regulator transistor is damaged due to over current transistor (eg, due to the 47k resistor transistor circuit on the secondary error detector value is delayed).
- If the input ac voltage drops can cause the power regulator transistor is damaged, due to over current transistor If the secondary there is a power transistor short can cause damage over current regulator.
- Protectors are designed to make the SMPS SMPS "reliable will not be damaged" if there are things that go wrong as mentioned above. 

Switching Mode Power Supply protect Circuit
SMPS Circuit

SMPS circuit using IC systems generally are designed with a surge protector, which include:
  • Over voltage protector (OVP)
  • Over current protector (OCP)
  • Over load protector
  • Short circuit protector
  • Over temperature protector

Read More..